How an Atkinson Cycle Engine Works

Atkinson's U.S. patent (number 367,496, for us patent-adoring nerds) is pretty straightforward: about a thousand words of text and a few helpful diagrams. Or you can just read this explanation, which is far wittier than any patent.

The most common combustion engine these days is afour-stroke Otto cycle engine, where a piston goes up and down inside a cylinder and a spark ignites a mixture of gas and air. Same goes for an Atkinson cycle engine, so here's a quick refresher of the process:

Intake stroke:Sucks air and fuel into the cylinder

Compression stroke:Squishes the mixture so when the spark goes off, it will explode -- big time

Power or expansion stroke:Uses the force created by the explosion to move the piston down the cylinder

Exhaust stroke:Pushes the nasty leftovers of the combustion process out of the cylinder

In an Otto cycle engine, this is done in two rotations of the crankshaft: intake/ignition, then power/exhaust. In the original Atkinson engine, the inventor added a couple of linkages so that all four strokes could be completed with a single rotation of the crankshaft.

That in itself would improve efficiency, but Atkinson had another realization: if the compression in the cylinder were lowered and the power stroke was longer than the intake stroke, the engine would work more efficiently. It would take less fuel to turn the engine, which turns the wheels and makes the car go.

Imagine, if you will, the cylinder and piston. On the intake stroke, the piston doesn't move all the way down the cylinder. The intake valve, where the air and fuel enter the cylinder, doesn't allow as much of the mixture into the cylinder. Less mixture requires less compression. The piston moves back up for the compression stroke, and at the top the mixture is ignited. Boom! The force sends the piston back down the shaft of the cylinder in the power stroke, this time all the way down to take advantage of every last bit of force generated by the combustion. Then the piston moves back up to get the junk out for the exhaust stroke. Ta da! Four strokes, less fuel!

Of course, clever reader that you are, you probably realized that less fuel and less compression mean less power. You are correct. Even though the piston is allowed to travel further down on the power stroke than it does on the intake stroke, it's not going to generate as much power as it does in an engine with higher compression and a richer gas mixture.

The other challenge with this engine is that it requires lots of extra parts, which makes it tricky to assemble, not to mention expensive. Poor Atkinson had to achieve all this efficiency with springs and vibrating links and a red-hot ignition tube, which sounds like an excellent name for a band. Modern engineers have a much easier time of it.

Purists will pooh-pooh the Atkinson cycle engine of today, with nary a vibrating link in sight. As a matter of fact, if you put a modern Atkinson cycle engine next to a modern奥托循环发动机, you wouldn't be able to see any difference. "There's nothing in [the Prius] engine that's not in the regular engine," according to David Lee at the University of Toyota. (It's not a university you can attend unless you're a Toyota employee needing to know about the latest and greatest rolling out to the dealerships. Sorry.)

What Atkinson had to achieve with crankshaft placement we now can do withvariable valve timing, a far cheaper and easier solution. Remember that in Atkinson's original, the intake valves would close early to keep out some of the air-fuel mixture. Nowadays, the intake valve is held open a little too long, so that when the piston moves up for the compression stroke, a little of the gas-air mixture can escape. Each method has the same end: the compression ratio is lower. In engineer-speak, the modern method is known as "livic" -- late intake valve closure. Then thespark plugdoes its thing -- sparking -- and the piston takes advantage of the combustion with a full power stroke down the cylinder. And then the exhaust stroke does its clean-up job.

More than that has changed in 120-plus years. In the quest for increased efficiency, new materials have been developed. Lighter-weight pistons, rings, and valves springs, for instance, reduce friction and the overall weight of the car. Hauling less weight around takes less energy. Using adual-overhead cam engine, as Ford does in its Fusion and other hybrids, makes it even easier to control the process.

And again, clever reader, you probably noticed that the modern version of this engine produces less power, just like its predecessor. Too true. As Lee noted, "This engine would struggle in a regular car."

But you know where it doesn't struggle? In ahybrid drivetrain.

So, you've got anenginethat's really efficient, but it lacks in power, especially of the torque variety, the kind of power that the fire-breathing drag car has in spades. But, if you're ahybrid powertrainengineer, you also have anelectric motorthat has all torque all the time, from 0 rpm. The problem with the electric motor is that it doesn't sustain a high speed very well, not as well as a gasoline engine does, with its higherhorsepower. What to do, hybrid powertrain engineer?

好吧,如果你是吉尔伯特。波特兰迪,发生了be a hybrid powertrain engineer with Ford, or any other engineer at almost any other car company building full hybrids, you bring these two systems together likechocolateand peanut butter. At low speeds, the electric motors kick in with their torque and move the car forward. Unless you're one of those super carefulhypermilerswho press the accelerator as gently as if a kitten were hiding underneath it, thegasolineengine will come online pretty quickly, though the electric motor is doing quite a bit of work. At about 40 mph or so, the Atkinson cycle engine will take over almost completely, with a bit of assist from the electric motor.

As long as you've got this kind of combo, you can engineer the Atkinson cycle engine to mesh precisely with the electric motor for optimal efficiency. If you insist on taking on the fire-breather in the next lane, you won't be left completely in the dust. "Smash the pedal, and you'll get what you're asking for -- all of both powerplants," said Lee at Toyota.

这个负载均衡就是像T全混合动力的原因oyota Prius or Ford Escape get better mileage around town than they do on the highway -- exactly the opposite of, like, every other vehicle on the road. The non-fire-breathers among us drive pretty slowly around town. We start and stop a lot, and we don't get up to 75 mph, so the electric motor takes a lot of the burden. On the highway, though, the gasoline engine is pretty much working alone.

Hardly anyone in 1887 could have predicted the happy peanut butter-and-chocolate marriage between Atkinson's engine and electric motors -- cars didn't even have permanent roofs then.